manualshive.com logo in svg

Hitachi ZW 550-6, Operator'S Manual

The Hitachi ZW 550-6 is a robust and efficient construction machine designed for heavy-duty work. To harness its full potential, it is imperative to utilize the Operator's Manual. Get the comprehensive manual for this product, available for free download at manualshive.com, and optimize your productivity and performance on the field.

Share
Download
background image

OPERATOR'S STATION

1-105

115MNEC-07-01

1

2

Power Mode Selector Switch

Two operation modes are available and can be selected 

by power mode selector switch (1) depending on the 

applications.

Each time the switch is pressed, the power mode is 

activated (ON) and deactivated (OFF) alternately. 

Power 

mode 

(ON)

: The power mode is suitable for 

heavy digging work prioritizing work 

effectiveness. 

Under auto shifting mode, the gear is 

shifted in regular engine RPM's (min

-1

) and 

shift mapping. 

Power 

mode 

(OFF)

: When the power mode is turned OFF, the 

machine operates putting more emphasis 

on lowering fuel consumption. 

Under auto shifting mode, the gear is 

shifted with lower engine RPM's (min

-1

) 

and shift mapping. 

When the power mode is activated, the symbol (   ) is 

displayed on the power mode indicator of the monitor 

screen. 

2nd/3rd Speed Limit Switch (Option)

A three-position switch (1) is provided to enable the 

operator to limit the maximum gear to 2nd or 3rd range 

while driving in auto shift mode. This is used exclusively 

with the optional joystick steering without the steering 

wheel/shift lever. 

MNEC-01-016

95Z7B-1-112-1

1

2

Limit to 2nd Speed

Limit to 3rd Speed

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZW 550-6

Brands by name

Popular brands

Load more brands