manualshive.com logo in svg

Hitachi ZW 550-6, Operator'S Manual

The Hitachi ZW 550-6 is a robust and efficient construction machine designed for heavy-duty work. To harness its full potential, it is imperative to utilize the Operator's Manual. Get the comprehensive manual for this product, available for free download at manualshive.com, and optimize your productivity and performance on the field.

Share
Download
background image

OPERATING THE MACHINE

5-2

f

NOTE: 

1.  When applying lift arm control lever (1) in the "Raise" 

position (A), the lever is moved (F) until the lift arm reaches 

the position preset by the lift arm kickout. When the lift 

arm moves the preset position, lift arm control lever (1) 

automatically moves to the Neutral (N) position. 

2.  When applying bucket control lever (2) in the "Tilt" position 

(D) after bucket dump operation, the lever is moved (G) 

until the bucket reaches the position preset by the bucket 

auto leveler. When the bucket reaches the preset position, 

bucket control lever (2) automatically moves to the Neutral 

(N) position. 

3.  When pushing down lift arm control lever (1) to the "Float" 

position (C), the lift arm moves to the position preset by lift 

arm auto-leveler system and is held in that position. When 

the lift arm moves to the preset position, lift arm control 

lever (1) automatically moves to the "Neutral" (N) position. 

(Machine is equipped with the lift arm auto-leveler system)

f

NOTE:  When operating the machine in Float (C) position, 

first hold the lift arm at the float position; then further tilt 

the lever to the Float position, and lower the lift arm on the 

ground. 

M4GB-01-073

2

1

115Z7-1-92-1

C

B

E

N

N

A

F

G

D

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZW 550-6

Wacker Neuson WL 30 Operator'S Manual preview
WL 30
Brand: Wacker Neuson Pages: 246
Ingersoll-Rand 570811001 Service Manual preview
570811001
Brand: Ingersoll-Rand Pages: 41

Brands by name

Popular brands

Load more brands