manualshive.com logo in svg

Hitachi ZW 550-6, Operator'S Manual

The Hitachi ZW 550-6 is a robust and efficient construction machine designed for heavy-duty work. To harness its full potential, it is imperative to utilize the Operator's Manual. Get the comprehensive manual for this product, available for free download at manualshive.com, and optimize your productivity and performance on the field.

Share
Download
background image

OPERATING THE MACHINE

5-6

Adjustment of Bucket Auto Leveler

d

WARNING:  CRUSH HAZARD

  Be careful to avoid injury and/or death when 

adjusting the bucket auto leveler.

  Stop the engine. Lower the loader arm and bucket 

to the ground to release oil pressure. 

  Apply the parking brake to prevent unexpected 

movement of the machine. Chock wheels with 

blocks. Keep bystanders away from the vicinity of 

the machine.

The bucket auto leveler automatically stops the bucket 

movement when level. (When the machine is shipped from 

the factory, the bucket positioner is preset so that the bucket 

is stopped with the bucket bottom parallel with the road 

surface.)

For example, after discharging material into a truck or a 

hopper, when bucket control lever (4) is placed to detent 

position (G), the lever is held in that position. Then, when the 

bucket is returned to the preset angle position, the bucket is 

automatically stopped and the lever is returned to neutral (N).

The bucket auto leveler is preset so that when the bucket 

bottom becomes parallel with the road surface, bucket 

movement is stopped. Nevertheless, when required to tilt the 

bucket forward or backward beyond the level position, adjust 

the bucket auto leveler by moving the mounting position of 

the proximity switch (2), relative to rod (3).

 

95Z7B-5-6-1

2

3

M4GB-01-073

4

115Z7-1-92-1

C

B

E

N

N

A

F

G

D

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZW 550-6

Brands by name

Popular brands

Load more brands