manualshive.com logo in svg

Hitachi ZW 550-6, Operator'S Manual, Page: 358 / 438

Share
Download
Hitachi ZW 550-6 Operator'S Manual Download Page 358

MAINTENANCE

7-74

Check Drive Belt
--- every 10 hours (daily)
Adjust, Replace --- as necessary

Press the center of the belt with a hand, and check whether 

the belt deflects only slightly. 

Also, check the belt for a damage.

Measurement of Deflection Amount and Vibration 

Frequency

1.  Press the middle of the belt with a force of 98 N (approx. 

10 kgf, 22 lbf), and check whether the amount of 

deflection is within the following range. 

  Fan belt deflection value: 6~8 mm (0.2~0.3 in)

2.  When the value is not within the range, adjust the 

tension. 

3.  Check the belt for a damage such as a scratch and crack. 

4.  When the belt adjusting allowance is no longer available, 

when crack, damage or abnormal wear is found, or 

when the belt squeaks during driving even after the belt 

tension has been adjusted, replace the belt.

Adjusting Drive Belt

1.  Loosen idler pulley's lock nut (1). 
  Lock nut (1): 137~157 N·m (14~16 kgf·m, 101~116 lbf·ft)

2.   Turn the generator and idler pulley adjusting bolts (2, 3) 

to adjust the belt tension to be within the standard value 

range. 

3.   After the adjustment, firmly tighten loosened lock nut (1) 

to the specified torque.

Generator

95Z7-7-68-1

95Z7-7-68-2

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Reviews:

No comments