Hitachi ZW 550-6 Operator'S Manual Download

Page: 426 / 438

11-4

TROUBLESHOOTING

6. Drive Function

Problem

Cause

Solution

Joystick steering lever is heavy

to operate.

Faulty steering pump

* Repair, Replace

Faulty steering device

* Repair, Replace

Malfunction of steering cylinder

* Repair, Replace

Relief valve set pressure reduction

* Adjust

Low tire air pressure

* Inflate

Steering turns in unexpected

direction.

One side brake is applied or dragged.

* Adjust

Joystick steering operation is

not possible using the joystick

steering lever.

Joystick steering system is not turned on.

Turn the key switch on, lower the

armrest, turn the joystick steering

system switch on, and start the engine,

in this order. (Refer to page 3-3.)

Joystick steering lever failure (the switch

works but it will not steer).

* Repair, Replace

Armrest switch failure

* Repair, Replace

Controller failure

* Repair, Replace

Transmission shifting (F and R)

does not work using the joystick

steering F/R switch.

Joystick steering system is not turned on.

Turn the key switch on, lower the

armrest, turn the joystick steering

system switch on, and start the engine,

in this order. (Refer to page 3-3.)

F/R switch failure

* Repair, Replace

Armrest switch failure

* Repair, Replace

Controller failure

* Repair, Replace

Joystick steering system does

not turn off when the armrest is

fully raised.

Armrest switch failure

* Repair, Replace

Controller failure

* Repair, Replace

Defective wiring

* Repair, Replace

Joystick steering lever

movement is hard or stiff or

does not return to neutral when

released.

Defective joystick steering lever

* Repair, Replace

Accelerator pedal is heavy to

operate.

Rusted joint

* Lubricate, Repair

Accelerator pedal play is

excessive.

Worn joint

* Replace, Repair

Parking brake

Does not work properly

Worn brake disk and/or pads

* Replace

Faulty parking brake solenoid valve

* Repair or replace

Service brake does not work

properly

Malfunction of brake valve

* Repair or replace

Oil leak from brake line, Air mixing

* Repair. Bleed air

Service brake is dragging.

Malfunction of brake valve

* Repair or replace

Faulty brake pedal

* Repair or replace

Corrosion of brake pedal parts

Clean and lubricate

Pebbles in area of brake pedals

Remove - clean area

Service brake fluid loss

(hydraulic oil).

Oil leak from brake line and/or hose

connector

* Retighten or repair

Oil leak due to brake piston seal (inside axle)

* Repair

NOTE: * Consult the nearest authorized dealer.

(Continued)

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands

Hitachi ZW 550-6, Operator'S Manual

Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands