manualshive.com logo in svg

Hitachi ZW 550-6, Operator'S Manual

The Hitachi ZW 550-6 is a robust and efficient construction machine designed for heavy-duty work. To harness its full potential, it is imperative to utilize the Operator's Manual. Get the comprehensive manual for this product, available for free download at manualshive.com, and optimize your productivity and performance on the field.

Share
Download
background image

OPERATOR'S STATION

1-56

5.  Press selector knob (2) to display Rear View Camera 

Monitor screen (7).

6.  Press selector knob (2) to turn the rear view camera 

monitor ON/OFF/AUTO.

7.  When the rear view camera monitor is ON, rear view 

image is continuously displayed on the basic screen.

  When the rear view camera monitor is AUTO, rear view 

image is displayed on the basic screen only at reverse 

travel.

  When the rear view camera monitor is OFF, rear view 

image is not available.

IMPORTANT:  In order to obtain a clear image, clean the 

camera lens and the monitor display before operating 

the machine. In bad weather or extreme dust, more 

frequent cleaning will be required.

f

NOTE:  The monitor and camera lens surface is a resin 

(plastic) product. Lightly wipe the surface with a wet clean 

cloth. Never use an organic solvent.

IMPORTANT: 

 

Never attempt to change the mounting position of 

the rear view camera.

 

Consult your authorized dealer if any abnormality is 

found on the rear view image.

MNEC-01-006

2

7

MNHG-01-161EN

MNHG-01-162EN

MNHG-01-163EN

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZW 550-6

Brands by name

Popular brands

Load more brands