Hitachi ZW 550-6 Operator'S Manual Download

Page: 204 / 438

OPERATOR'S STATION

1-140

Rear Grille

WARNING: Open or close rear grille (4) only after

stopping the engine. It is very dangerous if you are

entangled in the cooling fan. Before operating the

machine, always check that the rear grille is well

latched.

NOTE: The starter key cannot be removed from latch (3)

while rear grille (4) is being opened.

Remove bolt caps (1) and bolts (2). Release latch (3) with

the starter key to unlock rear grille (4).

The rear grille opens and the cooling fan can be cleaned.

After closing rear grille (4), turn and remove starter key (3)

to lock rear grille (4). Tighten bolts (2) and install caps (1).

1,2

115Z7B-7-10-1

115Z7B-7-10-2

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands

Hitachi ZW 550-6, Operator'S Manual

Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands