manualshive.com logo in svg

Hitachi ZW 550-6, Operator'S Manual

The Hitachi ZW 550-6 is a robust and efficient construction machine designed for heavy-duty work. To harness its full potential, it is imperative to utilize the Operator's Manual. Get the comprehensive manual for this product, available for free download at manualshive.com, and optimize your productivity and performance on the field.

Share
Download
background image

MAINTENANCE

7-112

5.  Tap lock pin (1) into the flush ear using a hammer.

6.  Replace segments (6) with new ones.
  Segment mounting bolt tightening torque:  

1-1/4-7UNC bolt: 2402 N·m (245 kgf·m, 1772 lbf·ft)

7.  Retighten nuts (6) after a few hours of operation. 

Check and Replace Seat Belt and Lower Tether
Check --- every 10 hours (daily)
Replace --- every 3 years

Examine buckle (1), attaching hardware (2) and seat belt 

web. Replace the seat belt web, buckle, or attaching 

hardware if they are damaged, or worn. 

Also check the wind-up condition of the seat belt. 

Replace seat belt and lower tether every 3 years, regardless 

of appearance.

Check ROPS, ROPS Mounting Bolts, and Cab
--- every 10 hours (daily)

Check the appearance of ROPS (1) and Cab (3) for any 

abnormal damage or deformation.

Check the condition of ROPS mounting bolts (2). Retighten 

them, if loosened. 

Tightening torque: 

Bolt (2): 1421 N·m (145 kgf·m, 1048 lbf·ft)

1

2

115Z7-3-4-3

95ZV0017

2

1

MNHE-07-055

3

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZW 550-6

MASSEY FERGUSON MF 8925 XTRA Brochure preview
MF 8925 XTRA
Brand: MASSEY FERGUSON Pages: 11

Brands by name

Popular brands

Load more brands