Hitachi ZW 550-6 Operator'S Manual Download

Page: 203 / 438

OPERATOR'S STATION

1-139

Inspection/Maintenance Access Covers

CAUTION:



Always close side covers (1) and top cover (3)

when moving and/or operating machine.



Do not keep the side cover open on a slope or

when a strong wind is blowing. Failure to do so

may be dangerous because the side cover may

unexpectedly move or close.



Take care not to pinch fingers when opening/

closing side cover (1) and/or top cover (3).



When fully opening side cover (1), lock lever (5)

automatically slides and is positioned in the lock

position. Make sure that lock bar (5) is firmly

positioned to lock the cover.

To release the lock, pull wire (4) and release the

end of lock bar (5) from the lock position.



Never attempt to stand on fender (2) if side cover

(1) is provided with fender (2).

115Z7B-1-142-2

115Z7B-1-142-1

115Z7B-1-142-3

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands

Hitachi ZW 550-6, Operator'S Manual

Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands