Hitachi ZW 550-6 Operator'S Manual Download

Page: 383 / 438

MAINTENANCE

7-99

K. Air Conditioner

Clean/Replace Air Conditioner Circulation/Fresh

Air Filters
Clean filters --- every 100 hours (or once a week

whichever come first)
Replace filter --- after cleaning filters 10 times (or

when the filters are severely clogged)

Clean Fresh Air Filter

1. Remove the filter:
The fresh air filter is installed behind cover (1) on the

left rear side of the cab exterior.

Open cover (1) with the starter key.

2. Loosen wing nuts (3) and remove plate (2).

3. Remove fresh air filter (4).

WARNING: When using compressed air pressure,

wear safety glasses or goggles.

IMPORTANT:



If compressed air delivery pressure is high,

damage to the filter fins may result.



Always use compressed air at the lower pressure

than 0.2 MPa (2kgf/cm

, 30 PSI).



Keep the nozzle more than 500 mm (20 in) away

from the core surface.

4. Clean fresh filter (4) using compressed air.

IMPORTANT:



Incorrect installation of the filter may cause

dust to enter into the air conditioner, causing

malfunction or breakdown of the air conditioner.



Before installing the filter element, clean off

dust around the mounting area; install the filter

element with extra care.



Keep cab doors closed when operating machine.

3. Install the cleaned fresh air filter or a new filter by

following the filter removal procedure described in

step 1 in the reverse order.

115Z7-7-97-1

MNEC-07-043

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands

Hitachi ZW 550-6, Operator'S Manual

Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands