Hitachi ZW 550-6 Operator'S Manual Download

Page: 355 / 438

MAINTENANCE

7-71

F. Air Cleaner

Replace Air Cleaner Element
Outer element --- each time the monitor indicator

illuminates.
Inner element --- at the time of the fifth

replacement (or every 2 years) of the outer

element

Air cleaner (1) is comprised of double elements, outer

element (6) and inner element (5).

1. Park the machine following the same procedures as

described on page 7-6 for preparation of inspection/

maintenance work.

IMPORTANT: Do not allow foreign matter such as dirt

to enter the engine when replacing elements.

2. Remove clip band (3) and remove cover (2).

Clean out dust from inside cover (2) thoroughly.

3. Remove outer element (6) by slowly pulling it out.

Replace outer element with new one.

IMPORTANT: Do not reuse inner and outer element (5,

6).

4. In case the air filter restriction indicator lights soon

after replacing outer element (6), replace both outer

and inner elements with new ones.

Inner element (5) is threaded.

5. Confirm that gasket (7) fits properly onto cover (2).

6. Install cover (2) in the original position.

7. After replacing is complete, run the engine at slow

speed. Then, check that the air filter restriction

indicator is not ON.

95Z7B-7-69-3

95Z7B-7-69-2

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands

Hitachi ZW 550-6, Operator'S Manual

Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands