Hitachi ZW 550-6 Operator'S Manual Download Page 377

Page: 377 / 438

MAINTENANCE

7-93

Check Brake Disks (Service and Parking)
--- every 2000 hours

Service brake (1) is a closed wet type multi-plate hydraulic

brake, and is incorporated in the axle housing.

Parking brake (2) is also a closed wet type brake. Parking

brake (2) is mounted in the front axle.

Consult your nearest authorized dealer for checking.

Check Gas Pressure in Accumulator
--- every 2000 hours

Check the gas pressure at a regular interval. If the

machine is operated with the gas pressure lower than

specified value, normal brake performance and/or loading

performance may not be to specifications achieved,

possibly creating very hazardous situations. Ask your

nearest authorized dealer for checking.

NOTE: Check the accumulator for the ride control

equipped machine in the same manner.

115Z7-7-91-2

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands

Hitachi ZW 550-6, Operator'S Manual

Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands