Hitachi ZW 550-6 Operator'S Manual Download Page 357

Page: 357 / 438

MAINTENANCE

7-73

Check Coolant Level
--- every 10 hours (daily)

Check the coolant level at reservoir tank (1). The normal

coolant level is between the FULL and LOW marks on side

surface of reservoir tank (1).

In case no coolant is present in reservoir tank (1), add the

coolant mixture via cap hole (2) on reservoir tank (1).



When refilling a long life coolant (LLC), use the same

brand product and the same mixture ratio as already

used in the machine.



If only water is refilled, the mixture ratio in the long life

coolant (LLC) is diluted so that anti-rust and antifreeze

effect in the coolant will become diluted and less

affective.

IMPORTANT: If the coolant level is low, EGR cooler is

heated up, and damaged.

115Z7B-7-71-2

115Z7B-7-74-1

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands

Hitachi ZW 550-6, Operator'S Manual

Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands