manualshive.com logo in svg

Hitachi ZW 550-6, Operator'S Manual

The Hitachi ZW 550-6 is a robust and efficient construction machine designed for heavy-duty work. To harness its full potential, it is imperative to utilize the Operator's Manual. Get the comprehensive manual for this product, available for free download at manualshive.com, and optimize your productivity and performance on the field.

Share
Download
background image

OPERATOR'S STATION

1-76

Maintenance

The maintenance screen includes maintenance notice, 

remaining hours until the next maintenance, and maintenance 

intervals.

Maintenance Items

  Engine Oil

  Engine Oil Filter

  Hydraulic Oil

  Hydraulic Oil Pilot Filter

  Hydraulic Oil Return Filter

  Transmission Oil

  Transmission Oil Filter

  Front Axle Oil

  Rear Axle Oil

  Air Cleaner Filter Element

  Fuel Filter

  Air Conditioner Filter

  DEF/AdBlue® Supply Module Main Filter

  Fuel Solenoid Pump Filter

  Oil Separator Filter 

  User Setting 1

  User Setting 2

Maintenance Notice

1.  Press selector knob (2) while displaying Basic Screen (1) 

to display Main Menu screen (3).

2.  Rotate selector knob (2) to highlight Information Menu 

(4).

3.  Press selector knob (2) to display Information Menu 

screen (5).

4.  Rotate selector knob (2) to highlight Maintenance (6).

2

MNEC-01-006

5

6

3

4

1

MNHG-01-240EN

MNHG-01-103EN

MNHG-01-245EN-KC

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZW 550-6

Brands by name

Popular brands

Load more brands