Hitachi ZW 550-6 Operator'S Manual Download

Page: 180 / 438

OPERATOR'S STATION

1-116

Components Name

1- Monitor
2- Control Panel
3- Temperature Control Switch (Rotate)/Mode Switch

(Press)

4-  Defroster Switch
5-  Circulation/Fresh Air Switch
6-  Air Conditioner ON/OFF Switch
7-  Fan (Rotate)/Auto Switch (Press)

8- Defroster Vent
9- Rear Vent

10- Foot Vent
11- Air flows out of front vent and the defroster vents.

NOTE:



Except for the foot vent (10) and defroster vent (8), all

vents are provided with louvers to adjust the air flow

direction.



In addition, the louvers on front vent (11) and rear vent

(9) can be completely opened and closed by hand.

MNEC-01-006

115Z7-1-115-3

115MNEC-01-37

MNHG-01-103EN

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands

Hitachi ZW 550-6, Operator'S Manual

Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands