manualshive.com logo in svg

Hitachi ZW 550-6, Operator'S Manual

The Hitachi ZW 550-6 is a robust and efficient construction machine designed for heavy-duty work. To harness its full potential, it is imperative to utilize the Operator's Manual. Get the comprehensive manual for this product, available for free download at manualshive.com, and optimize your productivity and performance on the field.

Share
Download
background image

OPERATOR'S STATION

1-114

115Z7B-1-81-1

2

1

M4GB-01-089

1

3

Cigar Lighter (24 V DC Electrical Outlet)

Using Cigar Lighter

d

WARNING:  Never touch other than insulated the 

knob part. Otherwise, it may result in severe burns. 

IMPORTANT:  In case the cigar lighter does not pop out 

automatically after 30 seconds after pushing the 

cigar lighter in, pull out the cigar lighter manually. 

Then, consult the your nearest authorized dealer.

1.  Turn the key switch (1) ON.
2.  Press and release the lighter knob (2).
3.  The cigar lighter knob will return to the original 

position when the lighter becomes hot. Pull the cigar 

lighter out to use.

4.  After using the cigar lighter, insert the cigar lighter 

into the panel until the knob is seated in the original 

position and not pressed in. 

d

CAUTION:  Do not connect accessories that use 

power other than 24 V DC (MAX. 5 A). Damage to 

the batteries and accessories may result.

 

Do not use this socket to supply the power for a 

long time without running the engine. The batteries 

may be discharged.

Ash Tray

d

WARNING:  Take precautions against fires. 

Use this ash tray (3) when smoking in the cab. 

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZW 550-6

AVANT R35 Operator'S Manual preview
R35
Brand: AVANT Pages: 36
Quicke Q 900 Series Operator'S Manual preview
Q 900 Series
Brand: Quicke Pages: 171

Brands by name

Popular brands

Load more brands