manualshive.com logo in svg

Hitachi ZW 550-6, Operator'S Manual

The Hitachi ZW 550-6 is a robust and efficient construction machine designed for heavy-duty work. To harness its full potential, it is imperative to utilize the Operator's Manual. Get the comprehensive manual for this product, available for free download at manualshive.com, and optimize your productivity and performance on the field.

Share
Download
background image

OPERATOR'S STATION

1-23

  Engine Tachometer (1)

 

Engine tachometer (1) indicates the speed of currently 

running engine in a gauge form. (200 min

-1

 step or "RPM")

 

If the engine overspeeds, the color of the gauge changes. 

  ECO Indicator (2)

 

ECO indicator (2) lights when the engine runs in energy 

efficient condition.

 

It turns OFF when the driving speed is 2 km/h (1.2 mph) or 

lower or under heavy driving load. 

f

NOTE:  You may push the down shift switch when the ECO 

indicator goes OFF while operating on a slope or operation 

such as snow removal. (Refer to DSS (Down Shift Switch) 

section)

  Speedometer (3)

 

Speedometer (3) indicates the present driving speed.

  Transmission Oil Temperature Gauge (4)

 

Transmission Oil Temperature Gauge (4) depicts 

transmission oil temperature as a gauge. When the bar 

reaches the red range, the oil temperature is abnormal. 

If the oil temperature becomes abnormally high, the 

alarm buzzer will sound and the warning indicator will be 

displayed.

  DEF Level Gauge (5)

 

DEF level gauge (5) displays the remaining DEF amount. 

When DEF level becomes low, the last segment turns yellow. 

IMPORTANT:  If the engine runs with low DEF level, the 

engine power reduces gradually. When the gauge 

turns yellow, immediately refill DEF. (See page 1-33 for 

the alarm level.)

  Air Conditioner Display (6)

 

Air conditioner display (6) displays operating condition of 

the air conditioner.

  Ride Control Indicator (7) (Option)

 

Ride control indicator (7) is displayed when the ride control 

switch is in ON position.

  Seat Belt Indicator (8)

 

The indicator turns ON when the key switch is turned ON, 

and turns OFF 5 seconds after the engine starts.

1

2

3

4

5

6

7

8

MNHG-01-100EN

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZW 550-6

Curtis Sno-Pro 5FBMQA Assembly/Mounting Instructions preview
Sno-Pro 5FBMQA
Brand: Curtis Pages: 14

Brands by name

Popular brands

Load more brands