manualshive.com logo in svg

Hitachi ZW 550-6, Operator'S Manual

The Hitachi ZW 550-6 is a robust and efficient construction machine designed for heavy-duty work. To harness its full potential, it is imperative to utilize the Operator's Manual. Get the comprehensive manual for this product, available for free download at manualshive.com, and optimize your productivity and performance on the field.

Share
Download
background image

MAINTENANCE

7-38

Change Planetary Gear Oil

9.  Check that "TOP" mark (3) on the planetary gear 

housing comes top as shown. If not, move the 

machine and adjust the position. 

10.  Make sure to turn ON the parking brake switch, lower 

the attachment to the ground, and stop the engine. 

11.  Clean the vicinity of drain plug (5) and the oil drain 

plug hole.

12.  Arrange a container of 32.5 liters (8.6 gallons) 

capacity or larger to receive the drained oil. 

13.  Remove drain plug (5) to drain oil. 

f

NOTE:  Plug (5) can be also used to drain oil, when 

accessible.

14.  Securely tighten drain plugs (5). 

15.  Refill the specified amount of oil through oil level 

plug (4).

 

Supplied oil amount: 32.5 liters (8.6 gallons)/gear 

IMPORTANT:  It takes time for oil to fully lubricate the 

overall front axle. After installing the plug, operate 

the machine slowly for several minutes. Then, stop 

the engine and check the axle for any oil leaks.

16.  Check the oil level. (Refer to Check Axle Oil Level.)

f

NOTE:  Total amount of supplied oil is 180 L (47.6 gal) per 

axle assembly: 

 

Differential: 115 liters (30.4 gallons) 

Planetary gear: 32.5 liters (8.6 gallons) x 2

115Z7B-7-38-3

5

115Z7-7-40-2

3

4

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZW 550-6

MX MX TX420 User Manual preview
MX TX420
Brand: MX Pages: 36

Brands by name

Popular brands

Load more brands