manualshive.com logo in svg

Hitachi ZW 550-6, Operator'S Manual

The Hitachi ZW 550-6 is a robust and efficient construction machine designed for heavy-duty work. To harness its full potential, it is imperative to utilize the Operator's Manual. Get the comprehensive manual for this product, available for free download at manualshive.com, and optimize your productivity and performance on the field.

Share
Download
background image

OPERATOR'S STATION

1-41

2

MNEC-01-006

Lower Kickout ON/OFF, Stop Height Setting

  Rotate selector knob (2) to highlight ON (8).

  ON/OFF Selection

 

Press selector knob (2) to turn ON (enabled).

 

(A box next to ON turns green.)

 

This enables the setting of the lift arm height. 

 

Press selector knob (2) again to turn OFF (disabled).

 

When the lower kickout is ON (enabled), indicator 

 (12) 

will be displayed on the monitor.

  Display content

  Segment (10) indicates current set value of the lower 

kickout.

  Segment (11) indicates current height of the lift arm.

  Setting Operation

 

When the lower kickout is ON (enabled), the lift arm stop 

height can be set.

 

When the lift arm height changes by operating the lift 

arm control lever, the height is displayed on segment 

(11).

 

When the lift arm height is within the setting range, the 

mark 

 (9) will be displayed.

 

Rotate selector knob (2) to highlight 

 (9).

 

Press selector knob (2) to change the lower kickout 

setting value.

 

When the lower kickout setting value changes, the value 

will be displayed on segment (10).

8

9

10

11

12

MNHG-01-113EN

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZW 550-6

AVANT R35 Operator'S Manual preview
R35
Brand: AVANT Pages: 36
Bush Hog Front-Push Loader 2847QT Specifications preview
Front-Push Loader 2847QT
Brand: Bush Hog Pages: 1
Bush Hog M146 Operator'S Manual preview
M146
Brand: Bush Hog Pages: 39
Bush Hog 1747 Parts Manual preview
1747
Brand: Bush Hog Pages: 30
Bush Hog 3860 QT Operator'S Manual preview
3860 QT
Brand: Bush Hog Pages: 46

Brands by name

Popular brands

Load more brands