manualshive.com logo in svg

Hitachi ZW 550-6, Operator'S Manual

The Hitachi ZW 550-6 is a robust and efficient construction machine designed for heavy-duty work. To harness its full potential, it is imperative to utilize the Operator's Manual. Get the comprehensive manual for this product, available for free download at manualshive.com, and optimize your productivity and performance on the field.

Share
Download
background image

MAINTENANCE

7-46

Clean Suction Filter
--- each time the hydraulic oil is changed.

IMPORTANT:  This upper tank area must be very 

clean prior to beginning this procedure. Failure to 

clean the top of tank may lead to hydraulic system 

problems due to system contamination.

Two suction filters are located on the bottom of the 

hydraulic oil tank. Clean the suction filters when changing 

hydraulic oil.

1.  After draining hydraulic oil, remove cover (1) with 

gasket. Remove lock nuts (2) and washers (3), and 

remove suction filters (4) from the oil pipe.

  When removing the suction filter, take care not to 

allow trapped dust to fall into tank.

IMPORTANT:  A few small particles in the strainer 

is normal. Large metal, rubber pieces, or a large 

amount of fine particles is abnormal. If found, 

contact your authorized dealer. 

2.  Clean the suction filter and the hydraulic oil tank 

inside with cleaning solvent. Swab out cleaning oil 

with a lint free cloth.

3.  Install cleaned suction filters (4) to the oil pipe, and 

tighten lock nuts (2) with washers (3).

m

  : 38 N·m (3.9 kgf·m, 28 lbf·ft)

4.  Install cover (1) and a new gasket with nuts.

f

NOTE: Make sure to replace the cover gasket with new 

one.

5.  Fill the tank to level with the specified volume of oil 

through the oil supply port. Check the oil level at the 

oil sight gauge.

6.  Start the engine. While slowly raising or lowering the 

arm and tilting the bucket forward and backward, 

check for any abnormality. Stop the engine. Check 

the oil level using level gauge (5).

5

115Z7-7-39-1

1

2, 3

4

115Z7-7-42-2

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZW 550-6

Brands by name

Popular brands

Load more brands