manualshive.com logo in svg

Hitachi ZW 550-6, Operator'S Manual

The Hitachi ZW 550-6 is a robust and efficient construction machine designed for heavy-duty work. To harness its full potential, it is imperative to utilize the Operator's Manual. Get the comprehensive manual for this product, available for free download at manualshive.com, and optimize your productivity and performance on the field.

Share
Download
background image

SAFETY

S-36

Notes on Aftertreatment Device

About Aftertreatment Device

The aftertreatment device removes particulate matter (PM) 

and NOx (Nitrogen Oxide) from the exhaust gas. Follow the 

instructions below to prevent the aftertreatment device 

from being damaged.

d

WARNING:  Exhaust gas from the aftertreatment 

device, muffler, exhaust piping and tail piping 

becomes hot during and right after engine running 

and regeneration of aftertreatment device. Keep away 

from the exhaust system or hot gas from the exhaust 

piping during regeneration. Be careful to avoid skin 

contact with exhaust gas. It may cause severe burns.

  White smoke may be generated during aftertreatment 

device regeneration. Do not attempt to perform 

aftertreatment device manual regeneration in a badly 

ventilated area.

  Ammonia odor may occur during aftertreatment device 

regeneration temporarily, but is not a trouble.

  Do not touch water coming directly out of the 

aftertreatment device. The water is mildly-acidic by 

oxidation catalyst mounted in the aftertreatment device. 

If filter water spills on your skin, immediately flush it out 

with clean water.

Precautions for Communication Terminal

  Electrical wave transmitted from the communication 

terminal may cause malfunction of other electronic devices. 

Inquire to the device manufacturer for information on 

electrical wave disturbance when using an electronic device 

near the communication terminal.

  Never attempt to disassemble, repair, modify or displace 

the communication terminal, antennas or cables. Failure to 

do so may result in damage and/or fire to the base machine 

or to the communication terminal. (When required to 

remove or install the communication terminal, consult your 

authorized dealer.)

  Do not pinch or forcibly pull cables, cords or connectors. 

Failure to do so may cause a short or broken circuit that may 

result in damage and/or fire to the base machine or to the 

communication terminal.

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZW 550-6

Brands by name

Popular brands

Load more brands