Hitachi ZW 550-6 Operator'S Manual Download

Page: 82 / 438

OPERATOR'S STATION

1-18

Turn Signal Indicator (Green)

When the turn signal lever is operated, the turn signal and the

turn signal indicator start flashing.

High Beam Indicator (Blue)

When the head lights are used at the high beam position, the

indicator will light.

Work Light Indicator (Yellow)

When the work lights are turned ON, this indicator will light.

Clearance Light Indicator (Green)

When the clearance lights are turned ON, this indicator will

light.

Control Lever Lock Indicator (Red)

When the control lever lock switch is in ON position, the

control lever lock indicator will light.

M4GB-01-032

M4GB-01-033

M4GB-01-035

MNEC-01-004

MNDB-01-052

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands

Hitachi ZW 550-6, Operator'S Manual

Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands