manualshive.com logo in svg

Hitachi ZW 550-6, Operator'S Manual, Page: 55 / 438

Share
Download
Hitachi ZW 550-6 Operator'S Manual Download Page 55

SAFETY LABELS

S-43

1.  Bucket and Hood

d

CAUTION:  Sign indicates a fall 

hazard.

  Do not step on or stand in this area.

2.  Accumulator residual pressure

d

WARNING:  Oil injection hazard.

  Nitrogen accumulator contains 

compressed gas and fluid which could 

result in death or serious injury.

 

Release the oil pressure from all brake 

circuits before removing any oil lines or 

piping.

 

Do not attempt to service or repair an 

accumulator unless properly trained and 

equipped. 

115Z7B-S-43

label 44787-24470

label 44787-24370

115Z7B-S-53

115Z7B-S-44

115Z7B-S-49

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Reviews:

No comments