manualshive.com logo in svg

Hitachi ZW 550-6, Operator'S Manual

The Hitachi ZW 550-6 is a robust and efficient construction machine designed for heavy-duty work. To harness its full potential, it is imperative to utilize the Operator's Manual. Get the comprehensive manual for this product, available for free download at manualshive.com, and optimize your productivity and performance on the field.

Share
Download
background image

MAINTENANCE

7-11

Inspection and Maintenance Table

Check and/or carry out the maintenance at intervals of 

the specified operating hours below or the calender date, 

whichever comes first.

IMPORTANT

Severe applications require more frequent 

maintenance. Severe conditions include heavy dust, 

extremely abrasive material, caustic chemicals, 

extremely wet conditions or abnormally hot or cold 

ambient temperatures.

: First time replacement or cleaning only

Section

Item for check

Operating hours

Page

10

50 100 250 500 1000 2000 3000 4000 4500

Engine

Check Engine Oil Level

7-25

Check Coolant Level

7-73

Check DEF Level

7-106

Check Accelerator Pedal Operation, and 

Exhaust Gas Color and Noise

7-114

Check Pre-Filter Bowl (and drain if needed)

7-59

Check Fuel Level

7-57

Check Drive Belt (and adjust if needed)

7-74

Check Fuel Hoses

7-68

Replace Engine Oil and Oil Filter Element

7-26, 

7-28

Clean Radiator / Oil cooler Cores and Other 

Cooling System

*3 

7-79

Replace Fuel Main Filter

7-62

Replace Fuel Pre-Filter

7-64

Clean Fuel Supply Pump Strainer

7-66

Clean Fuel Priming Solenoid Pump Strainer

7-67

Drain Fuel Tank Sump

7-58

Check and Adjust Valve Clearance

7-116

Check Engine Compression Pressure

7-116

Check and Clean Starter and Alternator

7-116

Check Sound Absorbing Mat Around 

Engine

7-116

Replace DEF Supply Module Filter Element

7-109

Check and Adjust Engine Controller (ECM)

7-117

Check Turbocharger

7-117

Check Fuel Injector

7-117

Check Urea SCR System

7-117

Check Dosing Module

7-110

Replace DEF Tank Inlet Filter

As required, when DEF spills while filling

7-110

Replace Air Cleaner Element

Outer

Each time monitor indicator illuminates

7-71

Inner

At the time of the fifth replacement of the outer element 

(or every 2 years)

Change Coolant 

Every 2 years or 3000 hours 

7-76

Check and Clean Aftertreatment Device

As required, when regeneration indicator comes ON

7-104

f

NOTE:  *3: Shorten maintenance intervals when the machine is 

operated under severe conditions  

or when the machine is continuously operated for a long period of time.

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZW 550-6

ahlmann AL 150 Use And Maintenance Manual preview
AL 150
Brand: ahlmann Pages: 63
Mahindra 3535 Service Manual preview
3535
Brand: Mahindra Pages: 368

Brands by name

Popular brands

Load more brands