manualshive.com logo in svg

Hitachi ZW 550-6, Operator'S Manual

The Hitachi ZW 550-6 is a robust and efficient construction machine designed for heavy-duty work. To harness its full potential, it is imperative to utilize the Operator's Manual. Get the comprehensive manual for this product, available for free download at manualshive.com, and optimize your productivity and performance on the field.

Share
Download
background image

11-3

TROUBLESHOOTING

4. Control Lever

Problem

Cause

Solution

Hard to move

Rusted joint

* Lubricate or repair

Worn pusher

* Replace

Does not move smoothly

Worn pusher

* Repair or replace

Faulty pilot valve

* Replace

Does not return to neutral

Faulty pilot valve

* Replace

The lever is tilted in the neutral 

position due to increase in play

Worn joint

* Repair or replace

Faulty pilot valve

* Replace

The lever is not held with 

magnetic detent. 

Faulty magnetic solenoid 

* Replace

Faulty sensor

* Replace

5. Hydraulic System

After the machine has been kept stowed stored for a long 

time, air in the oil may be separated and accumulate in 

the upper section in the cylinder, causing slow response 

time in operation or reducing cylinder power. In case these 

symptoms appear, repeatedly operate all actuators several 

times.

Problem

Cause

Solution

Loader front and travel 

functions are inoperable 

(hydraulic pump noise level 

increases).

Faulty hydraulic pump

* Repair, Replace

Lack of hydraulic oil 

Refill

Broken suction pipe and/or hose

* Repair, Replace

All actuators have no power.

Malfunction due to worn hydraulic pump 

* Replace 

Decrease in set pressure of main relief valve in 

control valve

* Clean, Adjust 

Lack of hydraulic oil 

Refill

Trapped foreign matter in hydraulic oil tank 

suction filter

Clean

Aeration in suction side

Retighten

Only one actuator is inoperable. Broken control valve spool

* Replace

Trapped foreign matter in valve spool 

* Repair, Replace 

Broken pipe and/or hose

* Repair, Replace 

Loose pipe line joint 

Retighten 

Broken O-ring at pipe line joint 

* Replace 

Broken actuator

* Repair, Replace

Only one cylinder is inoperable 

or has no power.

Broken oil seal in cylinder 

* Repair, Replace 

Oil leaf due to damage to cylinder rod

* Repair, Replace

Oil overheats

Clogged oil cooler

* Clean, Replace

Slow fan speed

* Repair, Replace motor and pump

Weak tension of engine fan belt

Adjust

Oil leak from low pressure hose Loose clamp 

Retighten 

Faulty suction manifold

* Repair, Replace

f

NOTE:  * Consult the nearest authorized dealer.

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZW 550-6

Gehl HL 360 Operator'S Manual preview
HL 360
Brand: Gehl Pages: 40

Brands by name

Popular brands

Load more brands