manualshive.com logo in svg

Hitachi ZW 550-6, Operator'S Manual, Page: 176 / 438

Share
Download
Hitachi ZW 550-6 Operator'S Manual Download Page 176

OPERATOR'S STATION

1-112

Multi-Function Joystick Type

MNEC-01-043

1

DSS (Down Shift Switch)

Press DSS (1) to down shift the gear. 

Set the shift gear to 2nd speed for normal operation. 

By pressing DSS (1) while digging with the machine in 

forward, the gear automatically shifts to 1st speed, which 

increases drive force and digging force. 

Once forward/reverse switch (2) is set to reverse (R), the 

gear returns to 2nd speed. 

Press DSS (1) when ECO indicator (3) turns OFF while 

operating on a slope or during snow removal. In this case, 

the gear temporarily shifts down to 1st speed by pressing 

DSS (2), but it automatically returns to 2nd speed when 

traveling load is reduced. 

f

NOTE:  When in auto shift mode or manual shift mode, 

each time DSS (1) is pressed, the gear down shifts to 1st 

speed. When in auto shift mode, press and hold DSS (1) 

to down shift from 4th speed , 3rd speed, 2nd speed, and 

then to 1st speed. 

f

NOTE:   When DSS (2) is pressed during lockup shift range, 

the speed range is downshifted by one. (Pressing DSS 

during 4th L-UP moves down to 3rd shift range.)

f

NOTE:  This switch (2) works only in Manual traveling 

mode; has no function in AUTO1 or AUTO2 mode.  

Fingertip Control Type

1

115Z7-1-107-2

95Z7-1-85-1

2

3

MNHG-01-100EN

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Reviews:

No comments