Hitachi ZW 550-6 Operator'S Manual Download

Page: 271 / 438

OPERATING THE MACHINE

5-25

Removing Snow

WARNING: When operating a machine equipped with

ride control and the lift arm control lever in the float

position, when performing work as soil scooping, land

grading, or snow removal, be sure to turn the ride

control switch OFF. Failure to do so may allow the ride

control system to operate so that the front attachment

may automatically move up and down.

CAUTION: Remove snow in the same method as

employed in general loading work. However, pay

attention to slippage of tires traction and obstacles

that may be covered with snow.

Precautions for removing snow



Avoid sudden starting and stopping as well as rapid

steering of the machine.



Use tire chains on all four wheels.



Pay attention to the presence of the utility facilities such

fire hydrants, manholes, curbs, roadside drains, etc. The

facilities or the machine may be damaged.

Lifting Wheel Loader

WARNING:



Be sure to use lifting tools and set the articulation

stopper (lock bar) in the LOCK position. (Refer to

page 1-137.)



Never allow any person to ride on the machine to be

lifted.



Never allow any person to enter below the lifted

machine. Before fully lifting the machine above the

ground, check that the hooks are securely attached

to the machine and the machine is well balanced

while lifting the machine slightly above the ground.

Refer to the "LIFTING MACHINE" in the

TRANSPORTING section.

Lifting of the machine may be needed when loading

the machine onto a ship or truck for repairing and/or

transporting.

M4GB-05-019

115MNEC-05-01

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands

Hitachi ZW 550-6, Operator'S Manual

Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands