manualshive.com logo in svg

Hitachi ZW 550-6, Operator'S Manual

The Hitachi ZW 550-6 is a robust and efficient construction machine designed for heavy-duty work. To harness its full potential, it is imperative to utilize the Operator's Manual. Get the comprehensive manual for this product, available for free download at manualshive.com, and optimize your productivity and performance on the field.

Share
Download
background image

MAINTENANCE

7-6

"Raised" position 

115Z7B-1-10-3

5

Preparations for Inspection and Maintenance

d

WARNING:  If ride control switch (3) (option) is in 

the AUTO position, the lift arm may unexpectedly 

rise. To avoid an accident due to unexpected 

movement of the lift arm and bucket, always turn 

ride control switch (3) OFF before beginning the 

inspection and/or maintenance of the machine.

d

CAUTION:  If the machine is unexpectedly moved, 

a serious accident may result. Be sure to apply the 

parking brake when parking the machine.

Unless specified otherwise, park the machine by following 

the procedures below before beginning the inspection 

and/or maintenance work.

1.  Park the machine on a solid level surface.

2.  Lower the working tools such as the bucket level to 

the ground.

3.  Turn ride control switch (3) OFF.

4.  Set forward/reverse switch (4) on the joystick steering 

to the neutral position. 

Push the lock button and fully raise armrest (5) until it 

locks in the raised position. 

4

PUSH

115Z7B-4-4-1

F

R

N

4

2

3

1

115Z7B-1-9-4

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZW 550-6

TYM T603 Operator'S Manual preview
T603
Brand: TYM Pages: 121
ahlmann AL 150 Use And Maintenance Manual preview
AL 150
Brand: ahlmann Pages: 63
Komatsu WA470-8 Operation & Maintenance Manual preview
WA470-8
Brand: Komatsu Pages: 31
Bison VH-900 Series Operator'S Manual preview
VH-900 Series
Brand: Bison Pages: 31

Brands by name

Popular brands

Load more brands