Hitachi ZW 550-6 Operator'S Manual Download

Page: 134 / 438

OPERATOR'S STATION

1-70

5. Press selector knob (2) to display Display Item Selection

screen (7).

6. Rotate selector knob (2) to highlight Unit. Press selector

knob (2) to set the unit (Metric or US system).

7. Rotate selector knob (2) to highlight Accumulated

Operation Display. Press selector knob (2) to set the

display (hour meter) or ODO (odometer).

8. Before changing °C and °F, turn the blower of the air

conditioner ON.

Rotate selector knob (2) to highlight desired unit system

(°C or °F) (8). Press selector knob (2) to set the unit.

When pressing selector knob (2), "Wait." will be will be

displayed (9) and then the change will be completed.

MNEC-01-006

MNHG-01-221EN

MNHG-01-222EN

MNHG-01-223EN

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands

Hitachi ZW 550-6, Operator'S Manual

Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands