Hitachi ZW 550-6 Operator'S Manual Download Page 80

Page: 80 / 438

OPERATOR'S STATION

1-16

Air Filter Restriction Indicator (Red)

If the air cleaner element becomes clogged,, the air

filter restriction indicator and the service indicator light.

Immediately stop the engine and inspect the air cleaner

element. Replace the element, if necessary.

NOTE: This indicator may unexpectedly light when the

coolant temperature gauge indicates the center or lower

position.

It turns off automatically when the coolant temperature

increases.

Preheat Indicator (Yellow)

The engine is being preheated as long as the preheat indicator

stays ON. When the preheat indicator goes OFF, engine

preheating is completed.

M4GB-01-023

M4GB-01-031

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Search results

Summary of Contents for ZW 550-6

Reviews:

Hitachi ZW 550-6, Operator'S Manual, Page: 80 / 438

Search results

Summary of Contents for ZW 550-6

Reviews: