Hitachi ZW 550-6 Operator'S Manual Download

Page: 344 / 438

MAINTENANCE

7-60

5. After draining water, securely tighten drain (1) and

plug (3). Draining off of two pre-filters.

Tightening torque:
Drain (1): 2.5±0.5 N·m (0.25±0.05 kgf·m, 1.8±0.4

lbf·ft)

Plug (3): 10±2 N·m (1.0±0.2 kgf·m, 0.74±0.15 lbf·ft)

6. Start the engine. Check drain (1) and plug (3) for fuel

leaks.

IMPORTANT: After draining water from the fuel filter,

bleed air from the fuel supply system.

IMPORTANT: Do not use alcoholic gas dryer fuel

additives to remove water in fuel to avoid cracks in

the pre-filter transparent case.

Bleed Air from the Fuel System

Air in the fuel system may make the engine hard to start

or make it run rough or not run at all.

After draining water and sediment from the fuel

filter, replacing the fuel filter, cleaning the fuel pump

strainer or running the fuel tank dry, be sure to bleed

the air from the fuel system according to the following

procedure.

Air Bleeding Procedure

This machine is equipped with a fuel priming solenoid

pump (6).

CAUTION: Fuel leaks may lead to fires.

1. Turn the key switch to ON position. Fuel priming

solenoid pump (6) operates to help prime the fuel

system.

IMPORTANT: DO NOT start the engine.

2. Loosen air bleed plug (7) at the outlet port of fuel

priming solenoid pump (6).

Loosen air bleed plug (9) on supply pump (8).

Loosen air bleed plug (12) on fuel main filter (11).

95Z7-7-59-1

Pre-Filter

95Z7-7-59-2

115Z7B-7-61-3

[Machine RH Side]

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands

Hitachi ZW 550-6, Operator'S Manual

Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands