manualshive.com logo in svg

Hitachi ZW 550-6, Operator'S Manual

The Hitachi ZW 550-6 is a robust and efficient construction machine designed for heavy-duty work. To harness its full potential, it is imperative to utilize the Operator's Manual. Get the comprehensive manual for this product, available for free download at manualshive.com, and optimize your productivity and performance on the field.

Share
Download
background image

MAINTENANCE

7-55

Table 2. Lines

Interval (hours)

Check Points

Abnormalities

Remedies

Daily

Contact surfaces of 

flange joints

Leak (11)

Replace

O-ring and/or 

retighten bolts

Welded surfaces on 

joints

Leak (12)

Replace

Every 250 hours Joint neck

Crack (13)

Replace

Welded surfaces on 

joints

Crack (12)

Replace

Clamps

Missing

Replace

Deformation

Replace

Loose

Retighten

f

NOTE:  Refer to the illustrations in Fig. 2 for each check point location or for a description of 

the abnormality. Use genuine Hitachi parts.

M4GB-07-059

M4GB-07-060

12

13

12

Fig. 2

13

11

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZW 550-6

SDLG LG968 Operation & Maintenance Manual preview
LG968
Brand: SDLG Pages: 117

Brands by name

Popular brands

Load more brands