Hitachi ZW 550-6 Operator'S Manual Download Page 310

Page: 310 / 438

MAINTENANCE

7-26

Change Engine Oil
--- every 500 hours

WARNING: Immediately after the machine has

been operated, all engine parts are hot. Wait for

the engine to cool before starting any maintenance

work. Failure to do so may cause severe burns.

NOTE: Improper disposal of waste oil can threaten the

earth’s environment and ecology. Dispose the waste oil in

accordance with the local regulation and/or law. Be sure

to replace the engine oil filter when changing the engine

oil at the same time.

1. Park the machine following the same procedures as

described on page 7-6 for preparation of inspection/

maintenance work.

2. Clean the areas around the drain plug and the oil

filler.

3. Arrange a 60 liter (16 gallons) - capacity container to

receive the drain oil.

4. Loosen drain plug (3) provided on the fuel tank side

to allow oil to drain.

5. Drain oil from the oil filter cartridge.

115Z7B-7-28-3

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands

Hitachi ZW 550-6, Operator'S Manual

Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands