manualshive.com logo in svg

Hitachi ZW 550-6, Operator'S Manual

The Hitachi ZW 550-6 is a robust and efficient construction machine designed for heavy-duty work. To harness its full potential, it is imperative to utilize the Operator's Manual. Get the comprehensive manual for this product, available for free download at manualshive.com, and optimize your productivity and performance on the field.

Share
Download
background image

MOVING THE MACHINE

4-2

Starting to Move

d

WARNING:  Start to move the machine only after 

checking that no personnel and/or obstacles are 

present around the machine.

 

Never turn ride control switch (4) (option) to ON 

position when traveling the machine or raising 

the bucket. Before turning the ride control switch 

(4) ON, stop the machine and confirm that no 

one is around the bucket. Avoid turning ride 

control switch (4) to ON position while moving the 

machine. Failure to do so may automatically move  

the lift arm up or down.

Refer to page 1-109 for detailed information of ride control 

switch (4).

1.  Check that none of the warning indicators except 

parking brake indicator (1) on the monitor panel are 

ON when engine is running.

2.  Set the front attachment in the operating position by 

operating control levers (2) (3).

95Z7B-3-9-1

1

4

Multi-Function Joystick Type

MNEC-01-043

2, 3

Fingertip Control Type

4

2, 3

115Z7B-1-9-4

Position

A: 545 mm (21.5 in) 

115Z7B-4-1-1

A

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZW 550-6

SDLG LG936 Operation & Maintenance Manual preview
LG936
Brand: SDLG Pages: 122

Brands by name

Popular brands

Load more brands