manualshive.com logo in svg

Fujitsu MB90460 Series, Hardware Manual, Page: 564 / 739

Share
Download
Fujitsu MB90460 Series Hardware Manual Download Page 564

545

CHAPTER 20  8/10-BIT A/D CONVERTER

●

Clock selector

The clock selector selects the clock for activating A/D conversion. Either 16-bit reload timer channel 1

output or 16-bit free-run timer zero detection can be used as the activation clock.

●

Decoder

This circuit selects the analog input pin to be used based on the settings of the ANE0 to ANE2 bits and

ANS0 to ANS2 bits of the A/D control status register (ADCS0).

●

Analog channel selector

This circuit selects the pin to be used from eight analog input pins.

●

Sample and hold circuit

This circuit maintains the input voltage of the channel selected by the analog channel selector.  It samples

and maintains the input voltage obtained immediately after the activation of A/D conversion.  This circuit

protects the A/D conversion from any variations in the input voltage during approximation.

●

D/A converter

This circuit generates a reference voltage for comparison with the input voltage maintained by the sample

and hold circuit.

●

Comparator

This circuit compares the input voltage maintained by the sample and hold circuit with the output voltage

of the D/A converter to determine which is greater.

●

Control circuit

This circuit determines the A/D conversion value based on the decision signal generated by the comparator.

When the A/D conversion has been completed, the circuit sets the conversion result in the A/D data register

(ADCR0/ADCR1) and generates an interrupt request.

Summary of Contents for MB90460 Series




































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments