manualshive.com logo in svg

Fujitsu MB90460 Series, Hardware Manual, Page: 149 / 739

Share
Download
Fujitsu MB90460 Series Hardware Manual Download Page 149

130

CHAPTER 7  INTERRUPT

■

Hardware Interrupt Operation

Figure 7.4-2 shows hardware interrupt operation from generation of a hardware interrupt to the completion

of interrupt processing.

Figure 7.4-2  Hardware Interrupt Operation

(1) An interrupt cause is generated within the peripheral function.

(2) The interrupt enable bit of the peripheral function is referenced.  If the interrupt is enabled, the

interrupt request is output from the peripheral function to the interrupt controller.

(3) The interrupt controller that receives the interrupt request determines the priority of simultaneous

interrupt requests, then transfers the interrupt level (IL) that matches the corresponding interrupt

request to  the CPU.

(4) The CPU compares the interrupt level (IL) requested by the interrupt controller with the interrupt level

mask register (ILM).

(5) If the comparison indicates a higher priority than the current interrupt processing level, the CPU checks

the contents of the I flag in the condition code register (CCR).

(6) If in the check in (5) the I flag is interrupt enabled (I = 1), the CPU waits until the execution of the

instruction currently being executed terminates.  At termination, the CPU sets the requested level (IL)

in the ILM.

(7) Registers are saved, and processing branches to the interrupt processing routine.

(8) The interrupt cause that was generated in (1) is cleared by software in the interrupt processing routine.

Execution of the RETI instruction terminates the interrupt processing.

Internal bus

Microcode

Check

Comparator

Other peripheral 

Peripheral function that generated 

Enable FF

Factor FF

Level Interrupt 

Interrupt controller

the interrupt request

functions

comparator

level IL

IL:
PS:
I:
ILM:
IR:
FF:

Interrupt level setting bit in the interrupt control register (ICR)
Processor status
Interrupt enable flag
Interrupt level mask register
Instruction register
Flip-flop

X

Summary of Contents for MB90460 Series




































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments