Fujitsu MB90460 Series Hardware Manual Download Page 123

Page: 123 / 739

104

CHAPTER 6 LOW POWER CONSUMPTION MODE

6.5.3

Stop Mode

Stop mode causes the source oscillation to stop and deactivates all functions. It
therefore saves the most power saving while data is being retained.

■

Switching to Stop Mode

Writing "1" to the STP bit of LPMCR triggers a switch to stop mode.

At this time, if the MCS bit of the clock selection register (CKSCR) is "0", the microcontroller enters PLL

stop mode. If the MCS bit of CKSCR is "1", the microcontroller enters main stop mode.

●

Data retention function

In stop mode, the contents of dedicated registers, such as accumulators and internal RAM, are retained.

●

Operation during an interrupt

Writing "1" to the STP bit of LPMCR during an interrupt request does not trigger switching to stop mode.

●

Pin state setting

Selection of whether the external pins retain the state they had immediately before switching to stop mode

or go to high-impedance with switching to stop mode can be controlled by the SPL bit of LPMCR.

■

Release of Stop Mode

The low power consumption control circuit releases stop mode. The release is caused by input of a reset or

by an interrupt.

Because the oscillation of the operating clock is halted before return to normal mode from stop mode, the

low power consumption control circuit puts the microcontroller into the oscillation stabilization wait state,

then releases stop mode.

●

Return to normal mode by a reset

When stop mode is released by a reset cause, the microcontroller is placed in the oscillation stabilization

wait and reset state after release from stop mode. The reset sequence proceeds after the oscillation

stabilization wait interval has elapsed.

●

Return to normal mode by a interrupt

If an interrupt request higher than level 7 is issued from a peripheral circuit during stop mode (when IL2,

IL1 and IL0 of the interrupt control register (ICR) are set to a value other than "111

), the low power

consumption control circuit releases stop mode. After release, the CPU handles the interrupt as it would

any other interrupts. However, the CPU starts after the main clock oscillation stabilization wait interval

specified by the WS1 and WS0 bits of the clock selection register (CKSCR) has elapsed. The CPU

executes processing according to the settings of the I flag of the condition code register (CCR), interrupt

level mask register (ILM), and interrupt control register (ICR). If the interrupt is accepted, the CPU

executes interrupt processing. If the interrupt is not accepted, the CPU resumes the execution with the

instruction that follows the instruction in which switching to stop mode was specified.

Summary of Contents for MB90460 Series




































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for MB90460 Series

Reviews:

Fujitsu MB90460 Series, Hardware Manual, Page: 123 / 739

Search results

Summary of Contents for MB90460 Series

Reviews: