manualshive.com logo in svg

Fujitsu MB90460 Series, Hardware Manual, Page: 166 / 739

Share
Download
Fujitsu MB90460 Series Hardware Manual Download Page 166

147

CHAPTER 7  INTERRUPT

7.6.5

Processing Time of the Extended Intelligent I/O Service 

(EI

2

OS) 

The time required for processing the extended intelligent I/O service (EI

2

OS) changes 

according to the following factors:

• EI

2

OS status register (ISCS) setting

• Address (area) pointed to by the I/O register address pointer (IOA)
• Address (area) pointed to by the buffer address pointer (BAP)
• External data bus length for external access
• Transfer data length

Because the hardware interrupt is activated when data transfer by EI

2

OS terminates, the 

interrupt handling time is added.

■

Processing Time (one transfer time) of the Extended Intelligent I/O Service (EI

2

OS)  

●

When data transfer continues

The EI

2

OS processing time for data transfer continuation is shown in Table 7.6-2 based on the EI

2

OS status

register (ISCS) setting.

Unit:Machine cycle (One machine cycle corresponds to one clock cycle of the machine clock, 

φ

).

As shown in Table 7.6-3, interpolation is necessary depending on the EI

2

OS execution condition.

Table 7.6-2  Extended Intelligent I/O Service Execution Time 

EI

2

OS termination control bit (SE) setting

Terminates due to termination 

request from the peripheral

Ignores termination request 

from the peripheral

 IOA update/fixed selection bit (IF) setting

Fixed

Update

Fixed

Update

BAP address update/fixed selec-
tion bit (BF) setting

Fixed

32

34

33

35

Update

34

36

35

37

Table 7.6-3  Data Transfer Interpolation Value for EI

2

OS Execution Time

I/O register address pointer

Internal access

External access

B/Even

Odd

B/Even

8/Odd

Buffer address 
pointer

Internal access

B/Even

0

+2

+1

+4

Odd

+2

+4

+3

+6

External access

B/Even

+1

+3

+2

+5

8/Odd

+4

+6

+5

+8

B:

Byte data transfer

8:

External bus using the 8-bit word transfer

Even: Even-numbered address word transfer

Odd: Odd-numbered address word transfer

Summary of Contents for MB90460 Series




































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments