manualshive.com logo in svg

Fujitsu MB90460 Series, Hardware Manual, Page: 118 / 739

Share
Download
Fujitsu MB90460 Series Hardware Manual Download Page 118

99

CHAPTER 6  LOW POWER CONSUMPTION MODE

6.5.1

Sleep Mode

Sleep mode causes the CPU operating clock to stop while other components continue 
to operate.
When the low power consumption mode control register (LPMCR) indicates a switch to 
sleep mode, a switch to PLL sleep mode occurs if PLL clock mode has been set.  
Alternatively, a switch to main sleep mode occurs if main clock mode has been set.

■

Switching to Sleep Mode

Writing "1" to the SLP and TMDX bit of LPMCR and 0 to the STP bit of LPMCR triggers a switch to sleep

mode.

At this time, if the MCS bit of the clock selection register (CKSCR) is "0", the microcontroller enters PLL

sleep mode.  If the MCS bit of CKSCR is "1", the microcontroller enters main sleep mode.

Note:

Since the STP/TMDX bit setting overrides the SLP bit setting when "1" is written to the SLP, STP
and "0" to TMDX bit at the same time, the mode switches to stop/time-base timer mode.

●

Data retention function

In sleep mode, the contents of dedicated registers, such as accumulators and internal RAM, are retained.

●

Operation during an interrupt request

Writing "1" to the SLP bit of LPMCR during an interrupt request does not trigger a switch to sleep mode.

If the CPU does not accept the interrupt, the CPU executes the next instruction.  If the CPU accepts the

interrupt, CPU operation immediately branches to the interrupt processing routine.

●

Status of pins

During sleep mode, all pins retain the state they had immediately before the switch to sleep mode.  The

once exceptions are the pins used for bus input/output or bus control.

■

Release of Sleep Mode

The low power consumption control circuit releases sleep mode.  Releasing is caused by the input of a reset

or by an interrupt.

●

Return to normal mode by a reset

When sleep mode is released by a reset, the microcontroller is placed in the reset state on release from sleep

mode.

Summary of Contents for MB90460 Series




































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments