manualshive.com logo in svg

Fujitsu MB90460 Series, Hardware Manual, Page: 545 / 739

Share
Download
Fujitsu MB90460 Series Hardware Manual Download Page 545

526

CHAPTER 18  DTP/EXTERNAL INTERRUPT CIRCUIT

●

Switching between the external interrupt function and the DTP function 

Switching between the external interrupt function and the DTP function is accomplished by the ISE bit of

the corresponding interrupt control register (ICR).  If the ISE bit is "1", the extended intelligent I/O service

(EI

2

OS) is enabled and the circuit executes its DTP function.  If it is "0", EI

2

OS is disabled and the circuit

executes the its external interrupt function. 

Note:

If multiple interrupt requests are assigned to a single ICR register, the interrupt level (IL2 to IL0) is
common to all of the interrupt requests.  As a rule, when one interrupt request uses EI

2

OS, the other

interrupt requests cannot use it. 

■

Operation of the DTP/external Interrupt Circuit 

Table 18.5-1 shows the control bits and interrupt causes of the DTP/external interrupt circuit. 

When DTP/external input requests are set, the resource will generate an interrupt request signal to the

interrupt controller whenever an interrupt cause indicated in the request level setting register (ELVR) is

received at the corresponding pin.  If the ISE bit is "0", the interrupt processing microprogram is executed.

If it is "1", the extended intelligent I/O service handling (DTP handling) microprogram is executed. 

Table 18.5-1  Control Bit and Interrupt Cause of the DTP/external Interrupt Circuit

DTP/external interrupt circuit

Interrupt request flag bit

EIRR: ER7 to ER0

Interrupt request enable bit

ENIR: EN7 to EN0

Interrupt cause 

Input of an effective edge or level to pin INT7 to INT0

Summary of Contents for MB90460 Series




































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments