Endress+Hauser Proline Prowirl F 200 Operating Instructions Manual Download Page 60

Page: 60 / 224

System integration

Proline Prowirl F 200 PROFIBUS PA

Hauser

System integration

9.1

Overview of device description files

9.1.1

Current version data for the device

Firmware version

01.01.02

• On the title page of the Operating Instructions
• On the transmitter nameplate
•

Firmware version

parameter

Diagnostics → Device information → Firmware
version

Release date of firmware version

01.2018

---

Manufacturer ID

0x11

Manufacturer ID

parameter

Diagnostics → Device information → Manufacturer ID

Device type ID

0x1564

Device type

parameter

Diagnostics → Device information → Device type

Profile version

3.02

---

For an overview of the different firmware versions for the device

9.1.2

Operating tools

The suitable device description file for the individual operating tools is listed in the table

below, along with information on where the file can be acquired.

Operating tool via
PROFIBUS protocol

Sources for obtaining device descriptions

FieldCare

•

www.endress.com

→ Download Area

• CD–ROM (contact Hauser)
• DVD (contact Hauser)

DeviceCare

•

www.endress.com

→ Download Area

• CD–ROM (contact Hauser)
• DVD (contact Hauser)

SIMATIC PDM
(Siemens)

www.endress.com

→ Download Area

9.2

Device master file (GSD)

In order to integrate field devices into a bus system, the PROFIBUS system needs a

description of the device parameters, such as output data, input data, data format, data

volume and supported transmission rate.
These data are available in the device master file (GSD) which is provided to the PROFIBUS

Master when the communication system is commissioned. In addition device bit maps,

which appear as icons in the network structure, can also be integrated.
With the Profile 3.0 device master file (GSD) it is possible to exchange field devices made

by different manufacturers without having to reconfigure.
Generally speaking two different GSD versions are possible with Profile 3.0 and higher.

• Before configuring, the user must decide which GSD should be used to operate the

system.

• The setting can be changed via a Class 2 master.

Summary of Contents for Proline Prowirl F 200

































































































































































































































Search results

Summary of Contents for Proline Prowirl F 200

Reviews:

Related manuals for Proline Prowirl F 200

Brands by name

Popular brands

Endress+Hauser Proline Prowirl F 200, Operating Instructions Manual

Search results

Summary of Contents for Proline Prowirl F 200

Reviews:

Related manuals for Proline Prowirl F 200

Brands by name

Popular brands