DAELIM DAYSTAR - Service Manual Download Page 67

Page: 67 / 214

6-11

Clutch, Gearshift

●

When replacing the primary drive gear, select
the gear which the paint mark, same colar of
R.crank case paint mark, is indicated.

Paint mark of crank case

Paint mark of primary drive gear

White

White(Primary drive gear A)

Blue

Blue(Primary drive gear B)

Yellow

Yellow(Primary drive gear C)

•

Select the correct gear. If not install the correct
gear, the back-lash between the drive gear and
driven gear is out of regulation and the noise of
gear occur.

Installation

●

Install the woodruff key into the key groove of
the crankshaft.

●

Align the primary drive gear key groove with
the crankshaft key and install the gear.

●

Install the washer.

●

Coat the nut with clean engine oil, and tighten
the lock nut.

●

Hold the flywheel with a flywheel holder.

●

Tighten the primary drive gear lock nut.

Torque : 6.5kgf-m(65N.m)
Tools:

Flywheel holder
Lock nut wrench, 20

24mm

Extension bar

CAUTION

△

Crankshaft

Woodruff Key

Key Groove

Lock Nut

Lock Nut Wrench 20X24mm

Extension Bar

Summary of Contents for DAYSTAR -























































































































































































































Search results

Summary of Contents for DAYSTAR -

Reviews:

Related manuals for DAYSTAR -

Brands by name

Popular brands

DAELIM DAYSTAR -, Service Manual

Search results

Summary of Contents for DAYSTAR -

Reviews:

Related manuals for DAYSTAR -

Brands by name

Popular brands