DAELIM DAYSTAR - Service Manual Download Page 64

Page: 64 / 214

Gear Shift Cam

Bolt

Spring

Drum Stopper Arm

6-8

Clutch, Gearshift

Installation

●

Install the drum stopper arm collar, spring,
stopper arm, and bolt. Tighten the bolts.

Torque:1.2kgf-m(12N.m)

Inspection

●

Check the gear shift spindle for wear or
damage.

●

Inspect the gear shift plate for deformation,
wear, or other damage.

●

Check the return spring and gear shift plate
spring for wear or damage.

●

Press the stopper arm, and install the cam,
aligning the dowel pin with the gear shift hole.

●

Install the thrust washer into the gear shift
spindle.

●

Install the gear shift spindle into the crank
case, aligning the teeth of the return spring
with the tappet of the right crank case as
shown.

Part

Collar

Stopper Arm

Thrust Washer

Gear Shift Spindle

Return Spring Teeth

Spring

Return Spring

Gear Shift Plant

Gear Shift Plate

Summary of Contents for DAYSTAR -























































































































































































































Search results

Summary of Contents for DAYSTAR -

Reviews:

Related manuals for DAYSTAR -

Brands by name

Popular brands

DAELIM DAYSTAR -, Service Manual

Search results

Summary of Contents for DAYSTAR -

Reviews:

Related manuals for DAYSTAR -

Brands by name

Popular brands