DAELIM DAYSTAR - Service Manual Download Page 117

Page: 117 / 214

10-12

Crank Case / Transmission / Crankshaft / Kick Starter

Installation

●

Coat the pinion gear with clean engine oil.
Install the gear into the 20mm thrust washer
and tighten them with the snap ring.

●

Install the kick starter ratchet into the spindle,
aligning the punch mark.

Crankcase Assembly

●

Install the dowel pins and a new gasket.

●

Install the spring retainer and kick starter
spring and insert the end of the spring pin into
the spindle hole.

●

Align the spindle collar end gap with the end
of the spring.

●

Install the 16mm thrust washer.

●

Install the 16mm thrust washer.

●

Install the ratchet spring into the ratchet guide
plate as shown and tighten them with the snap
ring.

●

Install the 12mm thrust washer.

Ratchet

Spring

16mm Thrust Washer

Dowel Pins

Gasket

Spring

Snap Ring

Guide Plate

Ratchet

16mm Thrust Washer

12mm Thrust Washer

Summary of Contents for DAYSTAR -























































































































































































































Search results

Summary of Contents for DAYSTAR -

Reviews:

Related manuals for DAYSTAR -

Brands by name

Popular brands

DAELIM DAYSTAR -, Service Manual

Search results

Summary of Contents for DAYSTAR -

Reviews:

Related manuals for DAYSTAR -

Brands by name

Popular brands