DAELIM DAYSTAR - Service Manual Download Page 59

Page: 59 / 214

6-3

Clutch, Gearshift

R. Crankcase Cover

Disassembly

●

Drain the engine oil(

⇨

2-3)

●

Remove the kick starter pedal.

●

Remove the clutch adjusting lock nut and
adjusting nut. Separate the clutch cable from
the clutch arm.

●

Remove the cable out of the cable holder.

●

Remove the right crank case cover bolt and
remove the cover.

●

Remove the dowel pins and gasket.

Clutch Arm/Lift Shaft Removal

●

Remove the lifter rod, and separate the clutch
arm/lift Shaft and clutch arm spring from the
R. crank case cover.

Kick Starter Pedal

Right Crank Case Cover

Dowel Pin

Clutch Arm

Lift Rod

Lifter Rod

Clutch Cable Holder

Summary of Contents for DAYSTAR -























































































































































































































Search results

Summary of Contents for DAYSTAR -

Reviews:

Related manuals for DAYSTAR -

Brands by name

Popular brands

DAELIM DAYSTAR -, Service Manual

Search results

Summary of Contents for DAYSTAR -

Reviews:

Related manuals for DAYSTAR -

Brands by name

Popular brands