DAELIM DAYSTAR - Service Manual Download Page 87

Page: 87 / 214

8-8

Cylinder Head / Valve

Valve Guide Replacement

•

When replacing the valve guide, valve seat
must be amended.

●

Heat the cylinder head equally to 130-140

℃

●

Avoid heating over 150

℃

•

Avoid performing the unskilled work. It is
caused a burn.

•

When heating the cylinder Head, do not heat it
sectionally using a gas burner. It is caused the
twist of cylinder Head.

●

Hold the cylinder head, and remove the valve
guide from the combustion chamber using
valve guide driver.

Tool : Valve guide driver

•

Avoid the cylinder head from damaging.

●

Install the new o-ring into the new valve guide.

●

Insert the valve guide in the top of the cylinder
head.

Tool: Valve guide driver.

●

After inserting the valve guide, install the
valve guide reamer in the combustion chamber
of the cylinder head and trim the valve guide.

CAUTION

△

CAUTION

△

CAUTION

△

Valve Guide Driver

Summary of Contents for DAYSTAR -























































































































































































































Search results

Summary of Contents for DAYSTAR -

Reviews:

Related manuals for DAYSTAR -

Brands by name

Popular brands

DAELIM DAYSTAR -, Service Manual

Search results

Summary of Contents for DAYSTAR -

Reviews:

Related manuals for DAYSTAR -

Brands by name

Popular brands