DAELIM DAYSTAR - Service Manual Download Page 92

Page: 92 / 214

8-13

Cylinder Head / Valve

Cylinder Head Installation

●

Clean the cylinder head surface of any gasket
materials.

●

Install the cam chain guide into the cylinder.

●

Install the dowel pins and a new gasket.

●

Install the cylinder head.

●

Install the cam shaft.

●

Install the engine into the frame(

⇨

Camshaft Installation

●

Install the rocker arm ring and rocker arm on
the camshaft holder.

●

Coat the rocker arm shaft with engine oil and
installl it into the camshaft holder.

●

Rotate the rocker arm shaft with a driver, align
the dowel pin hole and bolt hole of the cam
shaft holder and rocker arm shaft.

Cam Chain Guede

Dowel Pin

Rock Arms

Shaft

Bolt

Holes

Dowel Pin

Holes

Cam Shaft Holder

Summary of Contents for DAYSTAR -























































































































































































































Search results

Summary of Contents for DAYSTAR -

Reviews:

Related manuals for DAYSTAR -

Brands by name

Popular brands

DAELIM DAYSTAR -, Service Manual

Search results

Summary of Contents for DAYSTAR -

Reviews:

Related manuals for DAYSTAR -

Brands by name

Popular brands