DAELIM DAYSTAR - Service Manual Download Page 194

Page: 194 / 214

18-5

Electric Starter

Starter Magnetic Switch

Inspection

Turn the main ignition switch “ON”.
There should be phonic signal in battery
voltage while the starter magnetic switch is
depressed.

Tighten the two mounting bolts securely.
Install the starter motor cable, tighten the
terminal nuts securely.

Installation

Install a new o-ring into the front cover. Coat
the o-ring with oil and install the starter motor
into the crank case.

Align the rear cover with the case mark and
install the 2 setting bolts.
Tighten the setting bolts exactly.

O-Ring

Bolt

Starter Magnetic Switch

Rear Cover

Mark

Summary of Contents for DAYSTAR -























































































































































































































Search results

Summary of Contents for DAYSTAR -

Reviews:

Related manuals for DAYSTAR -

Brands by name

Popular brands

DAELIM DAYSTAR -, Service Manual

Search results

Summary of Contents for DAYSTAR -

Reviews:

Related manuals for DAYSTAR -

Brands by name

Popular brands