DAELIM DAYSTAR - Service Manual Download Page 169

Page: 169 / 214

15-8

Hydraulic Brake

Inspection

Inspect the caliper friction surface for
damaging or crack.
Measure the caliper inside diameter.

Service Limit: 34.02mm (1.339in)

Inspect the piston outside for damaging or
crack.
Measure the piston outside diameter.

Service Limit: 33.87mm (1.333in)

Assembly

Clean the piston seal, dust seal with brake
fluid, and install of caliper into the

part.

Install the piston into the caliper by the groove
side of piston faces the pad.

Coat the boot with the silicon grease.
Install the boot into the

part of caliper

exactly.
Install the pad spring to caliper. (

15-5)

Install the caliper pin bolt, and install the
caliper bracket to caliper.
Install the brake pad to caliper. (

15-5)

Caliper

Caliper Piston

Micro Meter

Pad Spring

Bush

PistonSeal

Dust Seal

Piston

Summary of Contents for DAYSTAR -























































































































































































































Search results

Summary of Contents for DAYSTAR -

Reviews:

Related manuals for DAYSTAR -

Brands by name

Popular brands

DAELIM DAYSTAR -, Service Manual

Search results

Summary of Contents for DAYSTAR -

Reviews:

Related manuals for DAYSTAR -

Brands by name

Popular brands