DAELIM DAYSTAR - Service Manual Download Page 26

Page: 26 / 214

3-4

Maintenance

Fuel Line

●

Check the fuel lines for deterioration, damage,
or leakage. Replace the fuel lines.

Throttle Grip Operation

●

Check the throttle grip for smooth operation.

●

Complete opening and automatic closing in
all steering positions.

●

Lubricate the throttle cables if throttle
operation is not smooth (

⇨

2-7)

●

Make sure if there is no deterioration,
damage, or kinking in the throttle cables.

●

Measure the throttle grip free play at the
throttle grip flange.

Free Play : 2~6mm(0.078~0.236in)

●

Adjust the free play by loosening the lock nut
and turning the adjuster. Tighten the lock nut.

●

Recheck the throttle free play.

Fuel Cock

Fuel Tube

Choke Cable

Lock Nut

Adjuster

Summary of Contents for DAYSTAR -























































































































































































































Search results

Summary of Contents for DAYSTAR -

Reviews:

Related manuals for DAYSTAR -

Brands by name

Popular brands

DAELIM DAYSTAR -, Service Manual

Search results

Summary of Contents for DAYSTAR -

Reviews:

Related manuals for DAYSTAR -

Brands by name

Popular brands